Garland H280 Manuale Utente

03/09/09 P/N 4523367 Page 1 H280-series Valve Overheat / Relocation Kit Instructions: RC Ovens Instructions for Applying Kit #4523368 This kit

03/09/09 P/N 4523367 Page 10 11) Assemble New Pilot Assembly  A colored line on the top of the pilot indicates the type of fuel used. A BLACK

03/09/09 P/N 4523367 Page 11  Reattach original igniter Connection of taped ignition wire end to original igniter  Attach flex tube to pi

03/09/09 P/N 4523367 Page 12  Attach new Robertshaw thermocouple to pilot assembly  Push the thermocouple all the way into its slot on the p

03/09/09 P/N 4523367 Page 13 13) Install New Burner  Ensure that the bracket at the tip of the burner locks onto the bracket attached to the o

03/09/09 P/N 4523367 Page 14 15) Reinstall Orifice Bracket  Refer to Step 5 for orifice bracket connections  Make sure that the orifice is i

03/09/09 P/N 4523367 Page 15 16) Reinstall Door Springs  Refer to Step 4 for door spring connections  For the door hinge with no microswitch

03/09/09 P/N 4523367 Page 16 17) Reinstall Igniter Bracket Refer to Step 3 for igniter bracket connections 18) Attach Main Burner Gas Line Flex

03/09/09 P/N 4523367 Page 17 19) Screw on Pilot Gas Flex Tube, Adjust Main Burner Gas Fitting  Remove the brass nut and ferrule originally on

03/09/09 P/N 4523367 Page 18 20) Install New Pilot Gas Tube  If a new 3/16” fitting (Part 4, Assembly Drawing) was installed on the pilot gas

03/09/09 P/N 4523367 Page 19 21) Connect Remaining Tubes and Thermocouple  The free end of each 7/16” flex tube from the valve should be fitte

03/09/09 P/N 4523367 Page 2 Instructions: 1) Remove Kick Plate  Unscrew and set aside  This kick plate will not be reinstalled. A replacem

03/09/09 P/N 4523367 Page 20 23) Attach Bracket to Oven For Standard Ovens:  Unscrew the two screws holding the orifice bracket to the lower

03/09/09 P/N 4523367 Page 21 24) Attach Valve Onto Bracket  The valve is attached to the bracket using the bolt and nut provided (Part 13 and

03/09/09 P/N 4523367 Page 22 25) Install New Kick Plate  The new kick plate (Part 14, Assembly Drawing) slants outwards to accommodate the val

03/09/09 P/N 4523367 Page 23 Installation Complete Installation Complete – Kick Plate Off Installation Complete – Kick Plate On

03/09/09 P/N 4523367 Page 3 3) Unscrew Igniter Bracket  Unscrew the two screws holding down the igniter bracket to the orifice bracket. L

03/09/09 P/N 4523367 Page 4  Pry upward with the screwdriver. While holding this position, unhook the oven door hinge link. Unhooked oven do

03/09/09 P/N 4523367 Page 5  For the door hinge with a microswitch:  Unscrew the microswitch bracket from the oven frame. It is important th

03/09/09 P/N 4523367 Page 6 5) Remove Orifice Bracket  After removing the igniter bracket, the orifice bracket will be held in place by a sin

03/09/09 P/N 4523367 Page 7 6) Install Extension Fitting (if applicable)  If pilot gas tube going into the valve already has an extension pie

03/09/09 P/N 4523367 Page 8 7) Remove Left and Right Front Shields  Both shields are attached to the upper support bar using 3 screws. L

03/09/09 P/N 4523367 Page 9 9) Unscrew Pilot Bracket from Oven Floor  The bracket is held down to the oven floor using two screws. This brack